During the process of turning the parts over, because the position and shape of the parts have changed, it is not only difficult to reposition them, but the accuracy may also decrease to some extent.
However, the Starlight Seven-Axis Linkage Machining Center does not have this problem at all. With the assistance of two seven-axis Mechanical Arm, they can completely replace humans to 'automatically flip' the parts.
Ultimately, this will greatly save time spent on repeated measurements of positioning accuracy, and by reducing the sequence of repeated measurements, the production speed of parts processing can be increased again.
It even complements the previously developed legless wheeled dual-arm experimental robot.
It is entirely possible to use experimental robots to place metal materials on the processing table, and then remove the parts and put them away after processing.
Finally, the experimental robot can be used to remove metal debris from inside the seven-axis machining center, preparing it for the next part processing.
It can be said that Xingtu Technology, which possesses the Artificial Intelligence Jarvis, has already achieved truly 100% fully automated and unmanned metal processing production in the field of metal machining!
Of course, putting aside other matters, for products like machining centers, production efficiency and fully automated production to reduce production costs are very important.
But more importantly, it is the machining accuracy. If the Starlight Seven-Axis Linkage Machining Center improves production efficiency but reduces machining accuracy.
Then it would undoubtedly be a failed product and would not be worth 66 million experience points, so processing precision is the most important factor to consider.
Driven by curiosity, Lin Feng closed his eyes slightly and began searching his mind for the knowledge that had just been imparted to him.
Soon, a look of surprise flashed in Lin Feng's eyes, because the precision of this seven-axis linkage machining center far exceeded Lin Feng's imagination.
The conventional machining accuracy of this seven-axis linkage machining can reach up to 0.0006mm, or 700 nanometers, in micro-polishing mode.
When using the specially designed micro-cutting equipment 'nano flying knife cutting machine', its highest cutting precision can reach 0.0001mm, which is an ultra-high precision of 100 nanometers.
The so-called 'nano-knife cutting machine' is essentially a super nano-knife made by using ultra-fine single-walled carbon nanotubes with a diameter of only a few nanometers.
This allows for the cutting of metal materials, achieving the effect of machining ultra-precision parts.
Speaking of which, there's an Operation Guzheng in the TV series "The Three-Body Problem". In the series, someone uses 'nano flying knives' hundreds of meters long to cross the entire river like iron chains.
Subsequently, a warship, while sailing across the river, unknowingly passed through the iron chain barrier made of single-walled carbon nanotubes, and was eventually cut into countless pieces by the 'nano-knife'.
Witnessing this scene, viewers around the world watching the TV series "The Three-Body Problem" were in an uproar, marveling at the power and terror of the "nano-knife".
The so-called 'nano flying knife' is actually based on single-walled carbon nanotubes, but reality is ultimately different from the TV series "The Three-Body Problem".
In the TV series "The Three-Body Problem," single-walled carbon nanotubes, or nano-knives, can reach lengths of hundreds of meters or more, capable of crossing a large river. In reality, however, they are far shorter than hundreds of meters.
Even a single-walled carbon nanotube of only 0.5 meters in length cannot be made. Currently, the longest single-walled carbon nanotube in the world is only 0.17 meters, and the manufacturing cost is extremely high.
However, although humans cannot currently produce such long single-walled carbon nanotubes, this does not mean that the super-strong cutting effects shown in TV dramas are fake.
Because the physical concept of 'cutting' is different from the common person's imagination of 'cutting', the common person's imagination of 'cutting' does not actually exist.
Because the energy required to break chemical bonds is too great, and cannot be met by the kinetic energy of an arm.
Therefore, the actual 'cutting' process is actually the thinnest part of the blade tip pressing against the surface of the object.
Because the power of the entire hand is concentrated on the thin surface of the small blade tip, the energy is highly concentrated at this time.
Ultimately, under this enormous force, the object touched by the blade tip will undergo shear deformation between two adjacent layers.
When the tensile stress caused by shear reaches a certain value, the interaction force between adjacent layers will cause them to break.
What follows is a repeated 'squeezing' process, which ultimately appears to humans as the object being cut open.
Therefore, ordinary people have no idea that what they thought was 'cutting' actually does not exist.
They didn't realize that, from a microscopic perspective, the knife wasn't cutting through matter, but rather 'squeezing' the forces between substances.
Once scientists deciphered this truth, it opened up a vast space for imagination, leading to the development of many practical tools.
This principle is frequently used in science fiction works, which is why the TV series "The Three-Body Problem" features the shocking plot of the Operation Guzheng.
Therefore, the 'nano-knife' in the Operation Guzheng is real, and the Operation Guzheng can be replicated in reality.
But the prerequisite is that you can manufacture single-walled carbon nanotubes that are hundreds of meters long and can span a large river.
If you can do this, you can naturally recreate the scene from the Operation Guzheng in the TV series "The Three-Body Problem" and directly cut a large ship into countless long iron bars!
At this time, the special micro-auxiliary machining equipment of the Starlight Seven-Axis Linkage Machining Center, the nano-flying knife cutting machine, is naturally an extraordinary thing.
The single-walled carbon nanotubes it uses have a diameter of only 2 nanometers, as for their length...
According to Lin Feng's knowledge, the longest single-walled carbon nanotube reached an astonishing 16 meters, breaking the current and previous world records.
After all, the longest single-walled carbon nanotube in the previous life was only 0.17 meters.
At this point, the longest single-walled carbon nanotube reached an astonishing 16 meters, which meant that its applications suddenly expanded.
If you twist and twist them together to make carbon nanotube wires and then make them into an electric motor, then it will be the world's best electric motor and generator.
Because single-walled carbon nanotubes have extremely high electrical conductivity and electron mobility, and very low electrical resistance.
Electrons can easily pass through single-walled carbon nanotubes without generating heat, making them the best material for wires.
Therefore, if it is applied to the field of electric motors or generators, there is no need to worry about the motor overheating and burning out, and the efficiency can be greatly improved!
In addition, single-walled carbon nanotubes have great potential for development in the fields of chips, batteries, capacitors, power grids, composite materials, sensors, and aerospace.
Of course, while the prospects are wonderful, it is not easy to make use of these single-walled Carbon Nanotube Wires, which can be up to 16 meters long.
Because this is just a Carbon Nanotube Wires with a diameter of only 2 nanometers.
The goal is to manufacture a carbon nanotube chip or a carbon nanotube sensor from a single-walled Carbon Nanotube Wires that is 2 nanometers in diameter and 16 meters long.
This requires a lot of effort and overcoming many technical and manufacturing challenges.